|
Does anybody make QUALITY hard rubber Handgun Grips?
--------------------------------------------------------------------------------
OK. I am looking for proper sized, not full of holes, flashed, warped and/or melted looking hard rubber Handgun Grip. I have several vintage revolvers and a couple of Colt semi-autos that need new Handgun Grips. What I find from my usual sources are not as good as the broken Handgun Grips I have. I need some Webley large 455 Handgun Grips too. Would Eagle Handgun Grips make a pair in faux ivory? (polymer resin)
Senior Member
Join Date: 05-04-2001
Posts: 2,123 For good quality rubber Handgun Grip try Hogue.
Their Handgun Grips are better quality AND better "feel" than any one else's.
Dfariswheel
View Public Profile
Find More Posts by Dfariswheel
12-11-2004, 02:10 AM #3
Sir William
Senior Member
Join Date: 10-13-2004
Posts: 2,382 You misunderstood me. I am searching for gutta percha type Handgun Grips. These were used on pistols in the early days. They look like black plastic.
Join Date: 05-04-2001
Posts: 2,123 That's going to be tougher.
Most of these are modern plastics, and these are probably all made by one, or at most two companies.
Quality seems to be OK, but nothing special.
Gun Parts Corporation sells the most models of them, some smaller companies sell selected models, but again, I think they are all actually made by the same company.
What I'd suggest is contacting Doug Turnbull.
Turnbull is likely the world's premier firearms restorer.
I'd bet he can direct you to a maker of high-quality Handgun Grips, since his specialty is restoring antique guns to factory-new condition and he'd almost HAVE to have a source of correct gutta percha replacement Handgun Grips.
http://www.turnbullrestoration.com/
Join Date: 06-21-2002
Posts: 1,123 I don't want to do it, but I'll tell you to check over at fleBay, lots of times the Handgun Grips you are looking for are not recognized for what they are and sell cheap. I'm up to a couple dozen sets of Handgun Grips from there and could have spent a small fortune getting them elsewhere.
FORGET IT if you want Colt or S&W factory Handgun Grips, they have gone insane in the last couple years. Start hitting garage sales if you want mainstream Colt or S&W Handgun Grips at reasonable prices.
Join Date: 03-17-1999
Posts: 6,779 I have bought Handgun Grips from Gun Parts Corp. for around a dozen guns to replace hard rubber Handgun Grips. The new ones are plastic, of course, but all that I have used were excellent copies and just about indistinguishable from the original. In fact, I have some guns with the original grip on one side and the repro on the other, and there is no difference I can see between them.
AFAIK, no one makes or sells new gutta percha Handgun Grips; for one thing, the natural product is not even harvested any more and if it were no one would use it since modern plastic is so much better. Some people wonder why gutta percha was used at all, but when those Handgun Grips were new they were fairly pliable and tough; the substance hardens and becomes brittle with age.
I will add one more note. I have put modern J frame wood Handgun Grips on some old .38 breaktop S&W revolvers. Incredible as it is, the critical distance from the inner curve of the frame to the grip pin did not change in nearly 70 years, even though about 1/4 inch was added to the bottom of the grip. A fine match is possible just by trimming the J frame Handgun Grips to match the breaktop frame. They don't look original, of course, but they look great.
Jim
__________________
Jim Keenan
Join Date: 10-13-2004
Posts: 2,382 LOL You too? I have done just that Jim. I have even made and glued in a wood spacer for pocket carry of an old S&W breaktop 38. A friend still pocket carries a S&W breaktop 38. I have been using Dixie Gun Works for most of my vintage parts. The hard rubber repro Handgun Grips that I have gotten lately are just not a good fit or finish. I will check Numrich. There are several H&Rs with broken or missing Handgun Grips. I have been putting S&W wooden Heritage Series Handgun Grips on round butt K frames.
Join Date: 10-16-2001
Location: South
Posts: 304 Do a search for North Carolina Ordnance
__________________
rkc
Join Date: 10-13-2004
Posts: 2,382 NC Ordnance!? I thought they were run out of business. Deceptive advertising, defective merchandise and those POJ brass frames for CAS that they were selling. I have heard and seen too many horror stories about NC Ordnance. Thanks but, no thanks. Bad juju.
Join Date: 03-17-1999
Posts: 6,779 Just for general info. The reason it is hard to get Handgun Grips that exactly fit the old guns is that the gun makers fitted Handgun Grips that were a little oversize and then polished the grip frame down along with the Handgun Grips. The Handgun Grips were then removed, numbered to the gun, and replaced after the gun was blued/plated. Much as grip makers have tried, they cannot get that kind of perfect fit.
|
