|
Wobbly pistol grips
--------------------------------------------------------------------------------
Is this a common problem for revolvers? I have one with walnut pistol grips. The screw is as tight as it ever could be, and is not loosening. Yet, when I pick it up, there is this little bit of wobble. It's not horrible. It's kind of a picky thing, I guess, but it bugs me. I am thinking there must be a way to tighten things up, but like many here, I don't want to dick it up. Doyou think something as simple as a light sanding would set things right? Other suggestions?
Join Date: 05-27-2004
Posts: 1,637 So, without being able to actually see what is happening, it sounds like you are saying the fastener is tight, but the item still wobbles. In that case, I'd say the wobble is due to a mismatch between the mating surfaces of the two parts.
Trouble is, you don't know there the trouble is - the pistol grip could be nonplanar, or the grip frame, or both. So removing material may not work out.
I'd try adding some malleable material that will conform to the two surfaces under pressure and fill in any gaps. Assuming that the grip screws put pressure between the pistol grip and grip frame, one suggestion would be to try some single layer grey cardboard, and slide that between the two of them - that might be 1/16" or thinner, and may be able to get rid of your wobble without any risk of making matters worse. Another material that might work would be a bicycle inner tube (just cut to a single layer) - it's about the same thickness, but will "flow" better than the cardboard under pressure.
__________________
“Am I not destroying my enemies when I make friends of them?”
“When I do good, I feel good. When I do bad, I feel bad. That's my religion.”
Abraham Lincoln
CarbineCaleb
View Public Profile
Send a private message to CarbineCaleb
Find More Posts by CarbineCaleb
07-23-2005, 07:11 PM #3
clt46910
Member
Join Date: 07-03-2005
Location: Indiana
Posts: 80
it seems that your pistol grips do not fit well. Look for spaces, loose places, or just not a good fit in the pistol grips.
You have several opitions, but the one best for you would be your choice. I would personally find other pistol grips. Some I liked.
Barring that, I would put spacers around the pistol grips I have and see what happens. Could be just a piece of paper for now or the edge of a card, sometimes does not take much.
Good luck on what you try.
__________________
Chuck in Indiana
clt46910
View Public Profile
Send a private message to clt46910
Send email to clt46910
Find More Posts by clt46910
Join Date: 10-13-2004
Posts: 2,373 I suggest a new set of pistol grips and throw out what you have. If they were aftermarket, they were not fitted properly. I tend to believe they were misaligned and shaped. The exposure to moisture or heat can change the fit of wooden pistol grips. If they are ivory or stag or bone or horn exotic pistol grips, rub vegetable oil into them. If the pistol grips are polymer resin, boil them in hot water and wipe them dry before reinstalling. I have had pistol grips that were drilled too large to secure onto the frame pin. I use superglue and sanding dust to fill the hole and then redrill the holes. If they are too small at the top arch to fit into the frame, there isn't much that can be done.
Join Date: 05-04-2001
Posts: 2,121 Poor fit of wood pistol grips is common, and the fix is fairly simple.
First, remove the screw and 1 side of the grip.
Move it around to spot the problem area.
It will be either at the top where the grip interlocks with the cut in the frame, or it'll be at the bottom where the grip fits over the cross pin on the lower part of the grip frame.
One you've found the mis-fit area, coat the frame around the area with a coat of wax. I use Johnson's Paste Floor wax. Put on a good coat, and DON'T wipe it off.
Mix up a bit a 5 minute epoxy and apply a little in the problem area.
Put the pistol grips on, and snug the screw down, being sure to align the two halves properly to the frame.
Let stand for 15 minutes, remove the pistol grips, and do the other side.
This is a permanent "fix".
Join Date: 09-29-2004
Posts: 291 Thanks for all the responses. I am going to try some of your suggestions out. I love this forum! I definitely see a space between the pistol grips if I wedge my thumbnail in there. I was actually thinking of maybe putting some cardboard or what have you, but with a space in between the two, it seemed as if my problem was more like misfit or mishapen, so I started wondering if sanding might do something. I will try your suggestions first.
Join Date: 05-27-2004
Posts: 1,637 A mountain bike innertube should be big enough to easily span grip frame if cut open, and will cost you about $3 at KMart. Just cut it to match the shape of the pistol grips and a little smaller so it will look neat, and I think that should do the trick - and it preserves both the pistol grips and the gripframe as is, so it can't make things worse.
__________________
“Am I not destroying my enemies when I make friends of them?”
“When I do good, I feel good. When I do bad, I feel bad. That's my religion.”
Abraham Lincoln
“Never express yourself more clearly than you are able to think.”
Niels Bohr
Crank? Crankier? Crankiest? Find out!
h
Join Date: 11-25-2004
Location: Maine
Posts: 2,022 You don't say what revolver or what grip. Is it a factory grip? I've had some problems in the past fitting pistol grips, and I was able to fix the problem with some very minor changes.
I have a GP-100, and purchased Houge wood pistol grips. I put them on, and they wobbled. I noted I couldn't get the screw to tighten. I called Houge. They sent me several different sized screws. I used the short screw, everything tightened, and goodby wobble.
Many revolvers have a take down pin near the bottom of the grip frame. I've had two sets of Eagles that didn't fit right because the holes in the wood pistol grips that accomodate the take down pin were not drilled deep enough. Took out my Dremel, and drilled the holes down until they fit right....
Hope this helps some...
Join Date: 05-30-2004
Posts: 277 i've had the same problem with a couple of different aftermarket pistol grips. My fix was the same as Defariswheel's. Except i used wood putty instead of epoxy. Either one should do the job.
magsnubby
View Public Profile
Send a private message to magsnubby
Send email to magsnubby
Find More Posts by magsnubby
07-26-2005, 03:55 PM #10
BBBS
Junior Member
Join Date: 07-23-2005
Location: ohio
Posts: 3 a small piece of electrical tape might help
Join Date: 08-11-2001
Posts: 1,138 Skateboad tape. Comes in diferent thicknesses and grits. Sticky side on the frame, rough side towards the pistol grips. Done.
The pistol grips fit, but you didn't permanently alter the gun.
__________________
From my cold dead hands.........
NRA certified pistol instructor
|
